Botulax (300)

Botulax 300U: Advanced Botulinum Toxin Formula for Precision Wrinkle Treatment

What is Botulax 300U?

Botulax 300U is a highly refined botulinum toxin formulation composed of over 99% active botulinum neuroprotein, with a total mass of 900. This advanced product is specifically designed to address the underlying causes of expression wrinkles by moderating the muscle activities that lead to the formation of skin folds, creases, and facial lines. Botulax 300U is widely used in both cosmetic and therapeutic applications, offering effective results in facial contouring and wrinkle reduction.

Application Areas for Botulax 300U

Botulax 300U is effective in treating various facial areas where wrinkles and lines are most prominent. The key application areas include:

• Forehead and Interbrow Zone: Ideal for smoothing deep forehead lines and frown lines.
• Nose Bridge: Targets wrinkles on the bridge of the nose, often referred to as “bunny lines.”
• Eyes, Nasolabial Folds, Chin, and Mouth Corners: Reduces crow’s feet, nasolabial folds, and fine lines around the mouth, enhancing overall facial appearance.
• Facial Contour Corrections: Provides a lifting effect, tightening the skin and restoring the natural shape of the face, commonly referred to as Botox lifting.

Administration Protocol for Botulax 300U

Injection Preparation: The preparation process is crucial for the safe and effective use of Botulax 300U. Follow these steps:

1. Sanitize your hands and wear medical gloves.
2. Remove the plastic cap from the Botulax 300U vial.
3. Clean the rubber stopper with an alcohol pad.
4. Draw up 6.0 ml of room-temperature sterile saline into a syringe.
5. Inject the saline into the vial through the rubber stopper.
6. Gently swirl the vial to mix the solution. Avoid shaking the vial to prevent foaming.
7. Allow the mixture to sit for 5 minutes before proceeding with the injection.

Procedure Technique: The technique for administering Botulax 300U will vary depending on the specific treatment area. Key procedures include:

• Frown Lines: Perform deep injections at the bony origin of the medial corrugator muscle. Ensure injection points are close to the brow to avoid causing eyelid ptosis.
• Crow’s Feet: Use intradermal injections targeting the lateral orbicularis oculi muscle. Care should be taken to avoid the zygomatic muscles to preserve the natural smile.
• Forehead Lines: Inject subdermally, ensuring injection points are at least 2 cm above the eyebrows to prevent complications.
• Brow Lift: Administer superficial injections just below the brow to achieve a lifting effect while preserving lower frontalis muscle action.
• Lower Eyelid: A single intradermal injection should be administered lateral to the mid-pupillary line, approximately 4–5 mm below the eyelid margin.
• Bunny Lines: Perform intradermal injections directly into the bunny-line area to smooth these specific lines.
• Nasal Tip Elevation: Subdermal injections at the base of the columella can help elevate the nasal tip.
• Gummy Smile: Treat with two sessions focusing on upper-lip elevators and the depressor septi nasi muscle to correct a gummy smile.
• Perioral Wrinkles: Superficial dermal injections around the mouth can be enhanced with hyaluronic acid for more pronounced results.

Post-Injection Care and Storage Guidelines

Post-Injection Care: After the procedure, it is important to minimize bruising and avoid certain activities. Patients should stay upright for up to 3 hours post-injection to ensure optimal results and reduce the risk of side effects. Avoid vigorous exercise, bending over, or lying down immediately after the procedure.

Storage and Reconstitution: Botulax 300U is supplied in powder form and should be stored in a refrigerator at a temperature of 2-8°C. Reconstitution should be done using either preservative-free saline or bacteriostatic saline, following the recommended dilution protocols to achieve the optimal concentration for treatment. The product should be stored in a hermetically sealed container to maintain its efficacy.

Shelf Life: Botulax 300U has a shelf life of 36 months from the manufacturing date, provided it is stored under the recommended conditions.

Composition of Botulax 300U

• Active Ingredient: Botulinum Toxin Type A (Hemagglutinin)
• Excipients: Sodium Chloride (1.8 mg), Human Albumin (Serum) (1.0 mg)

This carefully balanced composition ensures the high efficacy and safety of Botulax 300U, making it a trusted choice for cosmetic professionals and patients alike.